Termékek decortéx prémium (2)

Filler dermico sviluppato da Merz Aesthetics, progettato per migliorare la qualità della pelle attraverso una combinazione unica di acido ialuronico e glicerolo.Composizione Acido Ialuronico reticolato: 20 mg/ml Glicerolo: 17,5 mg/ml Tampone fosfato pH 7 Indicazioni d'Uso Migliorare l’idratazione e l’elasticità della pelle. Ridurre le rughe sottili e superficiali del viso. Trattare le depressioni causate da cicatrici atrofiche. Affrontare i segni del fotoinvecchiamento cutaneo. Modalità di Somministrazione Il prodotto è destinato all’iniezione intradermica da parte di un medico qualificato. Per migliorare l’elasticità e la compattezza cutanea, si raccomanda un piano di trattamento di tre sessioni, con iniezioni seriali nel derma medio e profondo, a intervalli di quattro settimane. È fondamentale eseguire il trattamento in condizioni di asepsi adeguate. Avvertenze: BELOTERO® Revive è controindicato in caso di: Ipersensibilità nota a uno dei componenti. Gravidanza e allattamento. Pazienti di età inferiore a 18 anni. Presenza di infezioni cutanee o sistemiche. Certificazioni Il prodotto è un dispositivo medico di classe III, conforme alle normative europee.

Protech AC-P Paint based on acrylic resins in aqueous emulsion, for interiors and exteriors, protective lamellar structure which, in addition to having an aesthetic effect, allows maximum filling, transpiration and very high resistance to mechanical and chemical light. The high coverage and expandability make this product extremely easy to apply. The special acrylic resins that compose it allow to obtain a film characterized by a rapid insensitivity to water even during the drying phase, with a consequent reduction of the "snail effect" in the event of atmospheric events. Protective and decorative finish painting of walls, facades, concrete products, plasters, masonry, natural stone, porous substrates in general. For old plasters, pay particular attention to the old pre-existing paints, which must be removed by careful scraping and brushing in order to obtain a healthy and non-friable support; then proceed with the application of Protech Fix AC fixative. When applying on new plasters, it is good practice to insulate the base with acrylic insulator or even better with a white or neutral microemulsion fixative. Avoid windy or cold days when applying. Do not apply on fresh or particularly alkaline substrates, respect a minimum carbonation period of at least four weeks. On large surfaces it is recommended to apply product from the same batch and always proceed wet on wet to avoid signs of recovery. Never operate with temperatures below + 5 ° C. Rainy weather, excessive atmospheric humidity and temperatures below + 8 ° C can greatly compromise drying with the possibility of washing off by rainwater even after several days. . DILUTION (by volume with drinking water) BRUSH 1st COAT: 15% a crossed coat or two coats 12-24 hours apart 2nd COAT: 10%. ROLLER 1st COAT: 10% 2nd COAT: 10%. SPRAY (through specific equipment) 1st COAT: 15/25% 2nd COAT: 15/25%. To avoid filming defects, being resin-based products in aqueous emulsion, the application temperature must be between + 5 ° C and + 35 ° C with relative humidity not higher than 60/70%. Do not apply under the direct action of the sun and wind. Do not apply on fresh or particularly alkaline substrates, respect a minimum drying period of the substrate of at least four weeks. It is also advisable for colored, not to use on large surfaces dyed with different production batches as slight differences between batch and batch are technically possible. Please check the color before application as we will not respond to any disputes regarding the shade of the applied product. From 0.20 to 0.30 liters of Protech AC-P for each square meter of surface to be painted. Pail 14 l